Intelix DIGI-VGA-F Manual de usuario descargar pdf (Pagina 2)

Specifications subject to change without notice.

Maximum Distance* 1920 x 1200 resolution 250 feet

1600 x 1200 resolution 350 feet

1280 x 1024 resolution 500 feet

1024 x 768 resolution 700 feet

800 x 600 resolution 850 feet

Video Bandwidth DIGI-VGA-R-F receive unit (250 feet): 120 MHz

DIGI-VGA-R-F receive unit (850 feet): 50 MHz

DIGI-VGA-S-F send unit: 350 MHz

Input Video Signal 1.2V p-p

Audio Frequency Response 20 Hz to 20 kHz

Audio Impedance 600 ohm

Audio Nominal Level 0-1.0V

Common Mode Rejection 60 dB

Unshielded Twisted Pair Maximum capacitance: 20 pf/foot

Cabling Specifications Impedance: 100 ohms @ 1 MHz

(24 gauge or lower solid Attenuation: 6.6 dB/1000 ft. @ 1 MHz

copper) Cat 5, Cat 5e, Cat 6, Cat 7 compatible

Send Unit Connectors One female HD15 input, one female HD15 output, one 1/8”

mini audio input, one 1/8” mini audio output, one shielded

RJ45 output, one USB type-B power connector, one DIN mini

power connector

Receive Unit Connectors Two female HD15 outputs, two 1/8” mini audio outputs, one

shielded RJ45 input, one DIN mini power connector

Max Units for Linking 3

Max Distance Between Links Distance based on resolution

Temperature Operating: 32 to 131 F (0 to 55 C)

Storage: -4 to 185 F (-20 to 85 C)

Humidity: up to 95%

Power Consumption DIGI-VGA-R-F receive unit: 12V/0.5A or 6W

DIGI-VGA-S-F send unit: 12V/0.2A or 2.4W

Brightness Front panel trim-pot on DIGI-VGA-R-F receive unit

Contrast (skew adj.) Front panel trim-pot on DIGI-VGA-R-F receive unit

Status Front panel video, audio, and power LEDs on both the DIGI-

VGA-R-F receive and DIGI-VGA-S-F send units

* Distances and picture quality may be affected by cable grade, cable quality, source and

destination equipment, RF and electrical interference, and cable patches. Intelix

specifications are based on straight-through cabling with standard-grade Cat 5.

Specifications

Troubleshooting

If your equipment malfunctions with DIGI-VGA-F baluns in place, follow the

troubleshooting procedures below:

1. Perform diagnostics on your equipment by following the manufacturer’s

instructions.

2. Check all the connections and the structured cabling system. Verify the RJ45

crimp pattern conforms to either EIA/TIA 568A or 568B standards.

3. Check the pin configuration on the structured cable.

4. The maximum operational distances over which the DIGI-VGA-F balun kit can

be transmitted is dependant on the equipment used and cable. Ensure that the

maximum recommended operational distances have not been exceeded.

5. Check that only twisted pair patch cords are being used.

6. Replace the DIGI-VGA-F balun kit with another DIGI-VGA-F balun kit that is

known to be working.

7. Adjust the brightness and contrast setting on the DIGI-VGA-R-F receive balun.

8. If you still cannot diagnose the problem, contact Intelix for support.

Specifications

Enclosure Metal

Dimensions DIGI-VGA-R-F receive unit: 6.25” x 1.25” x 3.25”

DIGI-VGA-S-F send unit: 6.25” x 1.25” x 3.25”

Shipping Weight DIGI-VGA-F: 4.0 lbs.

Ordering Information DIGI-VGA-F: includes one DIGI-VGA-S-F send balun, one

DIGI-VGA-R-F receive balun, two DC power supplies, and

one USB power cable

DIGI-VGA-R-F: includes one DIGI-VGA-R-F receive balun

and one DC power supply

DIGI-VGA-S-F: includes one DIGI-VGA-S-F send balun,

one DC power supply, and one USB power cable

Warranty 2 years

DIGI-VGA-R-F

Receive Unit

DIGI-VGA-S-F

Send Unit

1 2

Comentarios a estos manuales

Sin comentarios

Intelix DIGI-VGA-F Manual de usuario Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware Intelix DIGI-VGA-F