Specifications
Specifications subject to change without notice.
Maximum Distance* 330 feet
Bandwidth (3 dB) 5 MHz to 900 MHz
Supported Video Channels CATV 2-150, VHF channels 2-13, FM broadcast band
Insertion Loss <9 dB: 5-10 MHz
<3 dB: 10-900 MHz
Return Loss >10 dB: 15-370 MHz
>7 dB: 370-770 MHz
>10 dB: 770-900 MHz
Common Mode Rejection -20 dB or higher at 5-900 MHz
Unshielded Twisted Pair Maximum capacitance: 20 pf/foot
Cabling Specifications Impedance: 100 ohms @ 1 MHz
(24 gauge or lower solid Attenuation: 6.6 dB/1000 ft. @ 1 MHz
copper) Cat 3, Cat 5, Cat 5e, Cat 6, Cat 7 compatible
Connectors One (1) male F to one (1) RJ45
RJ45 Pinout 7 & 8, pair 4
Temperature Operating: 32 to 104 F (0 to 40 C)
Storage: 14 to 158 F (-10 to 70 C)
Humidity: up to 95%
Enclosure Black plastic
Dimensions 2.5” x 1” diameter
Weight 0.07 lbs (1.05 oz.)
Regulatory Approval FCC, CE
Ordering Information RF: single RF balun in bulk packaging
RF-PAC: two RF baluns in retail-ready packaging
Warranty 2 years
* Distances and picture quality may be affected by cable grade, cable quality, source and
destination equipment, RF and electrical interference, cable patches, channel frequency
and input power. Maximum distance of 330 feet at CATV channel 2. May require tilt
amplifiers at higher frequencies. Intelix specifications are based on straight-through
cabling with standard-grade Cat 5.
Contact Information
Intelix
2222 Pleasant View Rd.
Middleton, WI 53562
Intelix RF Broadband Video Balun
Installation ManualInstallation Manual
Installation ManualInstallation Manual
Installation Manual
The Intelix RF balun passively transmits broadband (RF) video over unshielded twisted
pair cabling, such as Cat 5. Used in pairs, the RF transmits video up to 330 feet, providing
a low-cost, versatile cabling solution which uses a building’s existing structured cabling
system.
The RF is ideal for private RF networks, guestroom TV and internet services, apartments
and condominiums, schools and universities, and corporate audio/visual environments.
The RF is designed for point-to-point connections only.
To install an RF balun, perform the following steps:
1. Turn off power and disconnect the video equipment by following the
manufacturer’s instructions.
2. Make certain that outlets and cross connects to which you will connect the RF
are configured properly and labeled appropriately to identify the circuit.
3. Verify the desired twisted pairs are not being used for other LAN or telephony
equipment.
4. Connect the video input from the source equipment to one of the two baluns. Two
RF’s are needed—one at each end of the run—and are interchangeable.
5. Connect a 4-pair structured cable, such as Cat 5, to the RJ45 connector on the
balun.
6. Connect the second balun’s video input to the destination equipment.
7. Connect the 4-pair structured cable attached to the first balun to the RJ45
connector on the second balun.
8. Power on the source and destination equipment and test for correct operation.
Installation
Caution: Do not attempt to open the balun housing. There are no user-serviceable parts
inside the RF. Opening the unit will void your warranty.
Caution: Do not connect the RF to a telecommunication outlet wired to
unrelated equipment. Making such a connection may damage the
equipment and/or balun. Please ensure all wiring is “straight-through.”
Caution: Do not mount the balun over equipment ventilation openings. Covering the
openings may cause the equipment to overheat.
Toll-free: 866-4-MATMIX
Phone: 608-831-0880
Fax: 608-831-1833
www.intelix.com
Note: When first powering on the source and destination equipment or
switching video through the balun, there may be a 2-3 second delay
followed by 12 seconds of yellow video. This is normal operation and
the result of the balun correctly syncing to the monitor.
(4 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales